For use with CO2 kegging system. Chill your beer in the keg for 24 hours, deliver CO2 for 15 minutes with The Stone, and it's ready to drink!
|
A 5 gallon co2 draft system which includes everything you need to put your homebrewed beer on tap!
|
Chrome faucet assembly that allows you to attatch a metal faucet directly to your ball lock keg. This eliminates the need for a plastic hand faucet with tubing.
|
A hand held co2 charger for making your draft system portable without bringing your co2 tank and regulator with. It uses a co2 cartridge to dispense the beer. Just pull back on the lever to inject a co2 charge into your keg. Keeps the beer fresh.
|
Convert your refridgerator into a draft system with this kit. For use with commercial style American Sanke Kegs. Comes complete with 5 lb. (empty) co2 tank, double guage regulator, Sanke universal tap, door shank, faucet & Handle, all tubing and fittings.
|
Large foam washer used to seal the door shank or co2 line shank when the shank is run through the fridge.
|
1/8 to 1/2 inch stainless steel hoseclamps. Works well on tubing up to 5/16. Works great on wort chillers or draft systems, the clamps will no trust!
|
Plastic covers that fit on to the ball or pin lock tank lid handles that push against the top of the keg to provide a tight fit and seal.
|
Spring valve that fits under the tank plug on a firestone challenger, John Wood 85, (General Beverage) keg.
|
Screws on to the tail end of the door shank to hook up your tubing coming from the liquid out of your keg.
|
Nut used on the tail end of the door shank when installing your beer line to it. Nut only! You may need the tailpiece and washer.
|
Black handled tap that fits into the top of the American Sanke kegs to run co2 in and liquid out of keg. The whole tap twists to lock into place and the handle locks down for dispensing the beer.
|
Metal wrench with a plastic handle used to tighten or loosen the chrome faucet when installed on a tower or on a door shank.
|
Use to go through the refridgerator door with a chrome faucet and a tailpiece, to dispense your beer without opening the fridge.
|
Black plastic 3 tall faucet handle that screws onto the chrome faucet for dispensing.
|
Oring that fits on your tank lid that seals the lid to the top of the tank. Will work on both ball and pin lock kegs.
|
1/4 to 1 stainless steel clamps.Works well on larger tubing for draftsystems. Will not rust!
|
Oring that fits under the co2 or liquid dip tubes on cornelius ball or pin lock kegs.
|
Brass garden hose thread fitting with a 3/8 barbed fitting for tubing to make a wort chiller or 3/8 hose.
|
Plastic picnic type faucet with 1/4 inch barbs on tail end for use with 1/4 inch i.d. tubing in draft systems. Has thumb lever for dispensing.
|
Plastic fitting that snaps on to the liquid side out tank plug on the ball lock kegs. 1/4 barbed fitting runs 1/4 tubing to the faucet.
|
Plastic fitting that snaps onto the co2 side tank plug on the ball lock kegs. Hooks up to the co2 line out from the regulator.
|
Plastic with metal bare that clips in to the liquid out tank plug on a pin lock coke style keg. Used to run liquid out to your faucet. 1/4 barbed fitting for 1/4 tubing.
|
Plastic with a metal base to clip on to the co2 tank plug on the pin lock coke style kegs. Use to run co2 from the regulator to the co2 in on the keg. Has a 1/4 inch barbed fitting for tubing.
|
CO2 regulator that screws on to the co2 tank and regulates the amount of co2 used to carbonate or dispense the beer. It has a guage to monitor the co2 left in the tank and another to monitor the co2 flow into the keg. It has a manual adjustment for changi
|
(EMPTY) cannot ship filled
|
Chrome outside faucet with a smooth bore inside to help prevent foaming. Use with the door shank to convert a refridgerator into a draft system, or faucet will work with any faucet tower.
|
Sealing o-ring that fits on to the liquid or gas tank plug on the top of your ball or pin lock keg. It seals where the ball lock fitting connects to the tank plug.
|
1/4 inch threaded nut with a 1/4 inch barbed fitting for tubing.
|
Oring that fits on top of the tank plug. It seals where the pin lock fitting connects to it.
|